Your over-the-range microwave is humming but the food stays cold, or it threw sparks and a puff of smoke. Call Acdc Appliance Repair and we connect you with a licensed, insured independent pro near Florence who services OTR, built-in and drawer microwaves.
The cabinet hides a high-voltage capacitor that can store a deadly charge even when the unit is unplugged. That single part is the reason microwave repair should go to a trained pro, not to a weekend project.
Acdc Appliance Repair is a free referral service. Our dispatchers listen to the symptom, then route the call to an independent local pro who handles microwave electronics and mounting work.
Each pro we connect you with runs an independent shop with the license and insurance local rules call for. Asking for proof on arrival is perfectly normal.
Some microwave parts cost more than people expect. You get a written, upfront quote from the technician before work begins, which lets you weigh it against buying new.
We look for a pro already working near Florence. A same-day slot opens up regularly when local pros have breathing room, and the arrival window gets set while you are on the line.
Expect an insulated discharge tool for the capacitor, a multimeter for diode and transformer checks, the model tech sheet, and a microwave survey meter to check for leakage after high-voltage work.
These cover the over-the-range, built-in wall, drawer and convection combo models that are worth repairing. Each starts with a safe capacitor discharge before any testing.
The fan spins, the light glows, the plate turns, and the coffee comes out cold. The usual suspects are the magnetron, the high-voltage diode, the capacitor, or the transformer. The technician tests each one with the power off and the capacitor discharged.
Blue flashes along the side wall usually come from a greasy or burnt waveguide cover, chipped cavity paint, or a damaged rack support on a convection model. Left alone, arcing can pit the cavity and ruin the magnetron.
The door has several interlock switches and a monitor switch that blows the line fuse if the others fail. A totally dead microwave often means that fuse did its job. If yours runs with the door open, unplug it now and do not use it again until it is checked.
When keys stop responding or the oven refuses to shut off at zero, the touchpad membrane or a welded relay on the control board is usually behind it. The pro tests the keypad matrix and the relays first so the right part gets ordered.
Because an OTR unit doubles as the hood over your cooktop, the vent side wears out too. The technician can replace a noisy fan motor, a burnt cooktop lamp, clogged grease filters, and the charcoal filter used on recirculating setups.
A plate that will not spin usually needs a turntable motor or a new coupler. OTR units that sag or rattle may have a loose wall bracket or top bolts pulled through the cabinet, which is a safety issue with a hot stove below.
Use this as a quick read before you call. Share what you see with the dispatcher, and the technician can bring the most likely parts.
| Symptom | Common cause | What the tech checks |
|---|---|---|
| Runs, light on, no heat | Magnetron, diode, capacitor or transformer failure | Each high-voltage part with the capacitor discharged |
| Completely dead, no display | Blown line fuse from a failed door switch | Fuse, interlock switches, monitor switch |
| Sparks or smoke inside | Burnt waveguide cover, chipped cavity paint | Cover, cavity surface, stirrer, rack supports |
| Keeps running at zero or with door open | Welded relay or failed interlock | Control board relays and door switch chain |
| Plate will not turn | Turntable motor or coupler | Motor continuity, coupler, roller ring |
| Vent fan loud or dead | Fan motor bearings, greasy filters | Fan motor, damper, grease and charcoal filters |
Most pros will be honest that a small countertop unit is cheaper to replace than repair. Over-the-range, built-in, drawer and convection combo models are different: they are pricier, they are sized to a cabinet opening or wall plate, and replacing one can mean new trim, new brackets and reworked ductwork.
Unplug it, leave the cover on, and call. A dispatcher answers day and night.
Tell the dispatcher what type of microwave you have, whether it sits over the range, in a wall, or in a drawer, and what it is doing. If you can, read off the model number from the tag inside the door frame.
An independent technician working close to Florence gets the job, and the dispatcher shares the arrival window. Same-day arrivals are routine when a local independent pro is free.
The technician unplugs the unit, discharges the capacitor with an insulated tool, and tests the high-voltage parts, door switches and control board. OTR models may need to come off the wall plate for access. You get a written, upfront quote before work starts.
Once the part is in, the technician runs a water heating test and, if the high-voltage side was opened, checks the door edges with a leakage survey meter. The technician typically documents the parts and labor warranty on the work order; ask for a copy.
Our over-the-range microwave went completely dark mid-popcorn. The technician found a blown line fuse, then traced it to a cracked door switch. He replaced both and showed me why the fuse would have blown again if he had only swapped the fuse.
The built-in in our wall oven stack hummed but did not heat. A new one would have meant a new trim kit too. The tech tested the diode and magnetron, replaced the magnetron, and checked for leakage with a meter before he left.
Blue sparks kept flashing inside the cavity. The technician pulled a waveguide cover that was charred from spatter, put in a new one, and told me how to wipe it down so it does not happen again.
The drawer microwave kept running even at zero, which scared us. The technician diagnosed a stuck relay on the control board, ordered the exact board, and installed it on a return visit.
When the light, fan and turntable all work but food stays cold, the high-voltage circuit has failed. The most common causes are a bad magnetron, a shorted diode, an open capacitor, or a burnt transformer. These parts carry lethal voltage, so let a trained technician test them.
No. Stop using it until it is checked. Sparks usually come from a dirty or burnt waveguide cover or chipped cavity paint, and continued arcing can damage the magnetron. If there is smoke, keep the door closed and unplug it if you can reach the cord safely.
A totally dark microwave often has a blown line fuse. The fuse usually blows because a door interlock switch failed and the monitor switch shorted the circuit on purpose. Replacing only the fuse is not enough; the technician tests the whole switch chain.
Frequently. Over-the-range and built-in units are expensive and fitted to the opening, so a new one brings its own installation costs. Small countertop models are usually better replaced. With a written quote from the pro in hand, you can make the call.
Please do not. The high-voltage capacitor can hold a lethal charge long after the unit is unplugged, and a slip with a screwdriver can be fatal. Leave the cabinet closed and let a trained pro use an insulated discharge tool.
You should request it after any magnetron, door or high-voltage repair. Many technicians run a survey meter around the door edges and vents as a final check that nothing is leaking.
We route microwave calls from houses, condos and apartments throughout Florence and nearby neighborhoods. Dispatchers send each job to an independent pro already working close to your address, which helps when an OTR unit needs a second set of hands to lift off the wall plate.
Someone answers around the clock. Calls after hours are typically scheduled for the first slot next morning, while daytime calls can become same-day visits when a nearby pro has room.
